Top 10 common forklift accidents ， forklift operation ought to take note of these matters ！.

Do not take too lightly the forklift at the office. If the procedure is bad, there will be major mishaps in mins, and there are several crashes involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front can not be found, resulting in a rolling crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Case 3: The width of the forklift freight goes beyond the permitted width of the route and hangs on the roadside rack, which virtually triggers an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the car when it rolled over and was crushed.
Forklift procedure ought to pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and afterwards start.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the load is secure and reputable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the job site or while driving, take care that there will be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique circumstances.
6. When the forklift is running, it must obey the web traffic rules in the factory and need to maintain a specific safety and security range from the lorry ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the load should not block the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory area is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold items and play a stabilizing function. .
12. If problems are found, they will certainly be repaired and reported in a timely fashion, and they will never run with health problems or conceal them.

filling and discharging.
1. When fork-loading items, the range in between the two forks need to be changed as required to make the load of both forks balanced and not skewed, and one side of the product ought to protest the rack. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and hurt people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as feasible under the lots, and it ought to be kept in mind that the fork tip must not touch other products or things. The load ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the lots is lowered to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork items at broadband and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift workers to take part in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not allowed to utilize the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake Stand-on Electric Pallet Stacker deal with to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be checked, and fuel, lubing oil and air conditioning water need to be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, check whether the pressure and temperature level are regular.
5. After the forklift is running, the exterior leak must likewise be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the automobile;.
2. When you come across someone before you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the low point of the cargo should be 0.3 m ~ 0.4 m above the ground;.
5. The turning need to not be as well sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not Stand-on Electric Pallet Stacker allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the contrary side of the area with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844